High heating capacity of up to 40 kg bearing

The SKF small induction heater TIH 030m combines high heating capacity with portability. The compact lightweight design makes the TIH 030m portable. Placing the induction coil outside the heater's housing allows the heating of bearings weighing up to 40 kg (88 lb). The induction heater is equipped with thermal overheating protection to reduce the risk of damage to the induction coil and the electronics. In addition to temperature mode, the TIH 030m is equipped with a time mode for heating components other than bearings. The induction heating system is supplied standard with three yokes and is available in two executions: 230V/50-60Hz and 100-110V/50-60Hz.

Please note

This English spoken video has subtitles. Please choose your language as applicable.

Features and benefits 

  • Compact lightweight design; just 20,9 kg (46.0 lb) facilitating portability
  • 2-step power setting and smaller yokes allow heating smaller bearings safely and at lower power consumption
  • Capable of heating a 28 kg (61.7 lb) bearing in just 20 minutes
  • Temperature mode pre-set at 110 °C (230 °F) to help prevent bearing over-heating
  • Automatic demagnetisation
Technical data 
Designation 
TIH 030M/230V 

TIH 030M/110V 
Description  Induction heater 
SKF m20 performance  28 kg (61.7 lb) 
Voltage, V/Hz  230V/50-60Hz or 100-110V/50-60Hz 
Bearing: 
- Maximum weight  40 kg (88 lb) 
- Maximum bore diameter  20 - 300 mm (0.8 - 11.8 in.) 
Temperature control: 
- Range *  0 - 250 °C (32 - 482 °F) 
- Magnetic probe  Yes, K-type 
- Accuracy (electronics)  ± 2 °C (± 3.6 °F) 
Time control: 
- Range  0 - 60 minutes 
- Accuracy  ± 0,01 sec. 
Application example : 
- bearing, weight, temperature, time 23136 CC/W33, 28 kg, 110 °C, 20m
Thermometer mode  Yes 
Bearing mode  Yes 
Power setting  2-step; 50% or 100% 
Demagnetisation according to SKF norms (automatic)  Yes (<2 A/cm) 
Can heat sealed bearings  Yes 
Can heat pre-greased bearings  Yes 
Error guiding codes  Yes 
Thermal overload protection  Yes 
Control panel  Control panel and LED display integrated in remote control 
Operating area (w x h)  100 x 135 mm (3.9 x 5.3 in.) 
Coil diameter  95 mm (3.7 in.) 
Dimensions (w x d x h)  450 x 195 x 210 mm (17.7 x 7.6 x 8.2 in.) 
Total weight, including yokes  20,9 kg (46.0 lb) 
Maximum power consumption  2,0 kVA 
Standard yokes  45 x 45 x 215 mm (1.7 x 1.7 x 8.4 in.) for heating bearings with bore diameter of 65 mm (2.6 in.) and larger. 
28 x 28 x 215 mm (1.1 x 1.1 x 8.4 in.) for heating bearings with bore diameter of 40 mm (1.6 in.) and larger. 
14 x 14 x 215 mm (0.5 x 0.5 x 8.4 in.) for heating bearings with bore diameter of 20 mm (0.8 in.) and larger 
Core cross section  45 x 45 mm (1.7 x 1.7 in.) 
Bearing support arms  Yes, foldable 
Yoke storage  Yes, internal integrated in foldable bearing support arms 
Cooling fan  No 
Swivel arm  No 
Housing material  Steel and glass filled polyamide 
* Maximum heating temperature capacity depends on the weight and geometry of the bearing or workpiece. The heaters can achieve higher temperatures, please contact SKF for advice.